PCM填充方式对三套管式相变储热单元影响的数值研究

韩中合; 邓小雨; 李恒凡

doi:10.19912/j.0254-0096.tynxb.2024-2332

欢迎来到能源电力期刊网！

English Version 期刊登录

您当前的位置：

首页 >

文章列表页 >

PCM填充方式对三套管式相变储热单元影响的数值研究

更新时间：2026-07-21

- PCM填充方式对三套管式相变储热单元影响的数值研究
- PCM填充方式对三套管式相变储热单元影响的数值研究
- 太阳能学报 2026年47卷第5期页码：479-488
- 作者机构：
- 作者简介：
- 基金信息：
- DOI：10.19912/j.0254-0096.tynxb.2024-2332
  中图分类号： TK02
- 网络首发：2026-06-04，
  
  纸质出版：2026
- 稿件说明：
移动端阅览
韩中合, 邓小雨, 李恒凡. PCM填充方式对三套管式相变储热单元影响的数值研究[J]. 太阳能学报, 2026,47(5):479-488.

韩中合, 邓小雨, 李恒凡. PCM填充方式对三套管式相变储热单元影响的数值研究[J]. 2026, 47(5): 479-488.
韩中合, 邓小雨, 李恒凡. PCM填充方式对三套管式相变储热单元影响的数值研究[J]. 太阳能学报, 2026,47(5):479-488. DOI： 10.19912/j.0254-0096.tynxb.2024-2332.

韩中合, 邓小雨, 李恒凡. PCM填充方式对三套管式相变储热单元影响的数值研究[J]. 2026, 47(5): 479-488. DOI： 10.19912/j.0254-0096.tynxb.2024-2332.

摘要

该文以三套管式相变储热单元为研究对象

首先分析相变材料填充率为30%~80%的单、双管填充模型在储热过程中液相分数和平均温度的变化趋势

对比PCM的总蓄热量、熔化时间和平均蓄热速率;其次

以融化时间和总蓄热量为评价指标

采用熵权法和TOPSIS法对PCM填充率进行评价

确定60%PCM填充率的储热单元储热性能最优

进一步分析PCM温度场和涡量的演变情况

揭示重力驱动自然对流增强传热的机理;此外以60%PCM填充率的单管填充模型为对象

研究PCM径向位置对传热性能的影响。结果表明

随着PCM填充率增大

单位蓄热率下降

总蓄热量增加;当填充率高于40%后

由于单管填充模型内漩涡生成速度快于双管填充模型

漩涡对自然对流起到强化作用

因此单管填充模型储热性能优于双管填充模型。PCM采用靠近外管壁的径向填充方法对漩涡的生成起促进作用

在外管径和PCM填充率不变条件下

PCM径向位置越靠近外管完全融化时间越短

融化性能越好。

Abstract

This study investigates triplex-tube phase change thermal storage units. First

the variation trends of liquid phase fraction and average temperature during the heat storage process for single- and double-tube filled models with phase change material （PCM） filling rates ranging from 30% to 80% are analyzed. The total heat storage capacity

melting time

and average heat storage rate of the PCM are compared. Secondly

using melting time and total heat storage capacity as evaluation metrics

the entropy weight method （EWM） and the Technique for Order Preference by Similarity to Ideal Solution （TOPSIS） method are applied to assess the optimal PCM filling rate. The results show that a 60% PCM filling rate yields the best thermal performance. Further analysis of the temperature field and vorticity evolution reveals the mechanism by which gravity-driven natural convection enhances heat transfer. In addition

a single-tube model with a 60% PCM filling rate is used to study the influence of the radial position of PCM on heat transfer performance. The results indicate that as the PCM filling rate increases

the unit heat storage rate decreases

while the total heat storage capacity increases. When the filling rate exceeds 40%

the vortex generation rate in the single-tube model becomes faster than in the double-tube model

leading to enhanced natural convection by the vortex. Therefore

the single-tube filling model exhibits superior thermal storage performance compared to the double-tube model. Furthermore

a radial PCM filling method closer to the outer tube wall promotes vortex formation. Under constant outer tube diameter and PCM filling rate

the closer the PCM is to the outer tube

the shorter the complete melting time and the better the melting performance.

关键词

Keywords

references

MAHDI M S, MAHOOD H B, MAHDI J M, et al.Improved PCM melting in a thermal energy storage system of double-pipe helical-coil tube[J]. Energy conversion and management, 2020, 203: 112238.

SONI V, KUMAR A, JAIN V K.Performance evaluation of nano-enhanced phase change materials during discharge stage in waste heat recovery[J]. Renewable energy, 2018, 127: 587-601.

吴丽梅, 刘庆欣, 王晓龙, 等. 相变储能材料研究进展[J]. 材料导报, 2021, 35(S1): 501-506.

SEDDEGH S, WANG X L, HENDERSON A D, et al.Solar domestic hot water systems using latent heat energy storage medium: a review[J]. Renewable and sustainable energy reviews, 2015, 49: 517-533.

于静梅, 刘耀鸿, 张凤忠, 等. 翅片强化相变储能蓄热性能的数值研究[J]. 太阳能学报, 2023, 44(6): 78-83.

ELSANUSI O S, NSOFOR E C.Melting of multiple PCMs with different arrangements inside a heat exchanger for energy storage[J]. Applied thermal engineering, 2021, 185: 116046.

YAO Y P, WU H Y.Pore-scale simulation of melting process of paraffin with volume change in high porosity open-cell metal foam[J]. International journal of thermal sciences, 2019, 138: 322-340.

BAZAI H, MOGHIMI M A, MOHAMMED H I, et al.Numerical study of circular-elliptical double-pipe thermal energy storage systems[J]. Journal of energy storage, 2020, 30: 101440.

MODI N, WANG X L, NEGNEVITSKY M.Melting and solidification characteristics of a semi-rotational eccentric tube horizontal latent heat thermal energy storage[J]. Applied thermal engineering, 2022, 214: 118812.

CHEN G J, SUN G X, JIANG D Y, et al.Experimental and numerical investigation of the latent heat thermal storage unit with PCM packing at the inner side of a tube[J]. International journal of heat and mass transfer, 2020, 152: 119480.

ZAIB A, MAZHAR A R, AZIZ S, et al.Heat transfer augmentation using duplex and triplex tube phase change material (PCM) heat exchanger configurations[J]. Energies, 2023, 16(10): 4037.

贾仲琪. 三套管式相变蓄热单元蓄放热特性的数值模拟研究[D]. 包头: 内蒙古科技大学, 2022.

MAHDI J M, LOHRASBI S, GANJI D D, et al.Accelerated melting of PCM in energy storage systems via novel configuration of fins in the triplex-tube heat exchanger[J]. International journal of heat and mass transfer, 2018, 124: 663-676.

YANG K, ZHU N, CHANG C, et al.Numerical analysis of phase-change material melting in triplex tube heat exchanger[J]. Renewable energy, 2020, 145: 867-877.

PATEL J R, RATHOD M K.Thermal performance enhancement of melting and solidification process of phase-change material in triplex tube heat exchanger using longitudinal fins[J]. Heat transfer: Asian research, 2019, 48(2): 483-501.

牛福新, 倪龙, 姚杨, 等. 三套管蓄能换热器的蓄热特性研究[J]. 湖南大学学报(自然科学版), 2011, 38(7): 69-72.

BAŞAL B, ÜNAL A. Numerical evaluation of a triple concentric-tube latent heat thermal energy storage[J]. Solar energy, 2013, 92: 196-205.

HE F, BO R F, HU C X, et al.Employing spiral fins to improve the thermal performance of phase-change materials in shell-tube latent heat storage units[J]. Renewable energy, 2023, 203: 518-528.

杨锡运, 刘欢, 张彬, 等. 基于熵权法的光伏输出功率组合预测模型[J]. 太阳能学报, 2014, 35(5): 744-749.

刘磊, 贺小明. 基于TOPSIS法的火电厂配煤方案安全性评价研究[J]. 煤炭技术, 2015, 34(8): 315-317.

王天东, 何子睿, 单晓芳, 等. 基于熵权-TOPSIS的光电光热制冷系统评价与分析[J]. 太阳能学报, 2023, 44(9): 229-235.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

翅片式光伏直驱电热相变蓄热墙体传热特性研究

多元纳米颗粒增强石蜡相变储热材料的热物理性能实验研究

双层相变材料复合水箱蓄热特性研究

管翅式相变储热系统结构/热源条件强化传热数值模拟研究

氧化石墨烯强化相变材料微胶囊悬浮液光热性能研究