再热器管异种钢焊缝断裂原因分析

吴奭登; 高岩; 盘荣旋

欢迎来到能源电力期刊网！

English Version 读者登录期刊登录

您当前的位置：

首页 >

文章列表页 >

再热器管异种钢焊缝断裂原因分析

发电技术论坛 | 更新时间：2025-09-28

- 再热器管异种钢焊缝断裂原因分析
- CAUSE ANALYSIS OF RUPTURE FAILURE OCCURRED ON WELD JOINTS OF DISSIMILAR STEELS USED ON REHEATERS
- 热力发电 2011年40卷第2期页码：91-93
- 作者机构：
  
  1. 广东电网公司电力科学研究院
  2. 华南理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：
  中图分类号： TG441.7
- 纸质出版：2011
- 稿件说明：
移动端阅览
吴奭登, 高岩, 盘荣旋. 再热器管异种钢焊缝断裂原因分析[J]. 热力发电, 2011,40(2):91-93.

WU Shideng1, GAO Yan2, PAN Rongxuan11.Guangdong Electric Power Research Institute. CAUSE ANALYSIS OF RUPTURE FAILURE OCCURRED ON WELD JOINTS OF DISSIMILAR STEELS USED ON REHEATERS[J]. Thermal power generation, 2011, 40(2): 91-93.
吴奭登, 高岩, 盘荣旋. 再热器管异种钢焊缝断裂原因分析[J]. 热力发电, 2011,40(2):91-93. DOI：

WU Shideng1, GAO Yan2, PAN Rongxuan11.Guangdong Electric Power Research Institute. CAUSE ANALYSIS OF RUPTURE FAILURE OCCURRED ON WELD JOINTS OF DISSIMILAR STEELS USED ON REHEATERS[J]. Thermal power generation, 2011, 40(2): 91-93. DOI：

摘要

通过宏观检查、拉伸试验、金相显微组织分析

对锅炉后屏再热器12Cr1MoV钢与TP304H奥氏体钢异种钢接头泄漏原因进行了分析。结果表明

12Cr1MoV侧熔合区为接头的脆化和断裂薄弱区

熔合线上的富碳层和楔形缺陷导致焊缝形成裂纹而泄漏。另外

12Cr1MoV和奥氏体钢焊缝金属线膨胀系数差别很大

在焊缝界面附近出现的明显热应力对裂纹的形成有一定的促进作用。

Abstract

Through macroscopic inspection

tensile test

and metallographic microstructure analysis

the causes leading to leakage on weld joints of dissimilar steels

i.e.12Cr1MoV steel and TP304H austenitic steel

have been analysed.The results show that the fussion zone at 12Cr1MoV steel side is the weak zone for enbrittlement and rupture of the weld joints

the carbon-enriched layer and the wedge-shaped defects on the fussion line lead to crack in the weld joints

resulting in leakage.In addition

the linear expansion coefficient of two said steels in the weld joints has very large difference

the obvious thermal stress appeared in the vicinity of interface in the weld joints has promoting effect for cracking.

关键词

Keywords

references

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

燃煤锅炉烟气冷却器典型故障及防范对策

电磁泄放阀辅阀改进

氧化皮脱落导致的过热器管爆管分析

锅炉“四管”泄漏事故发生的原因分析及对策

200MW机组高压加热器投入率偏低的原因分析及改进措施