CAUSE ANALYSIS OF HIGHER MAIN STEAM TEMPERATURE DURING ROTATION-IMPULSING TO START UP 600 MW SUPERCRITICAL UNIT AND ADOPTED MEASURES

doi:10.19666/j.rlfd.2006.11.011

English Version Reader LoginJournal Login

您当前的位置：

首页 >

文章列表页 >

CAUSE ANALYSIS OF HIGHER MAIN STEAM TEMPERATURE DURING ROTATION-IMPULSING TO START UP 600 MW SUPERCRITICAL UNIT AND ADOPTED MEASURES

更新时间：2025-09-28

- CAUSE ANALYSIS OF HIGHER MAIN STEAM TEMPERATURE DURING ROTATION-IMPULSING TO START UP 600 MW SUPERCRITICAL UNIT AND ADOPTED MEASURES
- Thermal Power Generation Issue 11, Pages: 32-34(2006)
- 作者机构：
  
  湖南省电力试验研究院
- 作者简介：
- 基金信息：
- DOI：10.19666/j.rlfd.2006.11.011
  CLC： TK227.1
- Published：2006
- 稿件说明：
移动端阅览
CAUSE ANALYSIS OF HIGHER MAIN STEAM TEMPERATURE DURING ROTATION-IMPULSING TO START UP 600 MW SUPERCRITICAL UNIT AND ADOPTED MEASURES[J]. Thermal power generation, 2006, (11): 32-34.
DOI：

CAUSE ANALYSIS OF HIGHER MAIN STEAM TEMPERATURE DURING ROTATION-IMPULSING TO START UP 600 MW SUPERCRITICAL UNIT AND ADOPTED MEASURES[J]. Thermal power generation, 2006, (11): 32-34. DOI： 10.19666/j.rlfd.2006.11.011.

摘要

大唐湘潭发电有限责任公司3号600 MW超临界机组在起动调试过程中

多次出现主蒸汽温度偏高的问题

分析认为其主要原因是燃烧热负荷小、蒸汽流量小、炉膛负压低、给水温度低、减温水与主蒸汽压差偏小等。对此采取以下措施:(1)加大燃油量到(18~24)t/h

增加燃烧热负荷;(2)炉膛负压控制在-600 Pa

增加油枪的根部风;(3)锅炉总风量控制在(500~550)km3/h

改善燃烧;(4)提高给水流量至(410~450)t/h

提高给水温度至90℃以上。实施后效果良好。

Abstract

During the process of commision debugging of 600 MW supercritical unit no.3 in Datang Xiangtan Power-Generation Co Ltd

problems of unexpected higher main steam temperature had repeatedly appeared.Through analysis

it is believed that the main causes are: small heat load of combustion

low flow rate of steam

low negative pressure in the furnace

low temperature of the feed-water

small deviation of differential pressure between desuperheating water and main steam etc..For these

the adopted measures are as follows:（1） to enhance flow rate of the fuel oil to 8-24 t/h for increasing the heat load of combustion;（2） to control negative pressure in the furnace at-600 Pa

for increasing air flow at the root of oil guns;（3） to control total air flow of the boiler in the range of 500

50 km

/h for impr

oving the combustion;（4） to enhance the flow rate of feed-water to 410

50 t/h

and enhancing the temperature of feed-water to above 90 ℃.After implementation

the problem of unexpected higher main steam temperature during the time of rotation-impulsing has been solved.

关键词

Keywords

references

Views

140

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

DEBUGGING OF A 1025t/h WSHAPED FLAME BOILER IN SHAOGUAN POWER PLANT

DEBUGGING OF DEH GOVERNING SYSTEM FOR 600 MW SUPERCRITICAL UNIT IN HUANENG QINBEI POWER PLANT AND CONTROL IMPROVEMENT

Research progress of conversion and utilization of upgraded lignite by hydrothermal dewatering

Current status and development of control technologies for PM2.5 and Hg during pulverized coal combustion

Research on coupling calculation method of combustion and hydrodynamics for water walls in ultra-supercritical double-reheat boilers

Related Author

马斌

徐齐胜

李乃钊

岑可法

王晓勇

高海东

史章峰

吴恒运

Related Institution

Zhejiang University

Guangdong Electric Power Test and Research Institute

Xi'an Thermal Power Research Institute Co., Ltd

State Key Laboratory of Clean Energy Utilization, Zhejiang University

AI问答

⁰