Analysis of the effect of crack face contact on stress intensity factors for a centrally cracked Brazilian disk

LI Nian-bin; DONG Shi-ming; HUA Wen

doi:10.16285/j.rsm.2017.08.029

English Version Journal Login

您当前的位置：

首页 >

文章列表页 >

Analysis of the effect of crack face contact on stress intensity factors for a centrally cracked Brazilian disk

更新时间：2026-06-25

- Analysis of the effect of crack face contact on stress intensity factors for a centrally cracked Brazilian disk
- Vol. 38, Issue 8, Pages: 2395-2401(2017)
- 作者机构：
  
  四川大学建筑与环境学院,四川,成都,610065
- 作者简介：
- 基金信息：
- DOI：10.16285/j.rsm.2017.08.029
  CLC： TU452
- Online First：05 June 2018，
  
  Published：2017
- 稿件说明：
移动端阅览
LI Nian-bin, DONG Shi-ming, HUA Wen. Analysis of the effect of crack face contact on stress intensity factors for a centrally cracked Brazilian disk[J]. 2017, 38(8): 2395-2401.
DOI：

LI Nian-bin, DONG Shi-ming, HUA Wen. Analysis of the effect of crack face contact on stress intensity factors for a centrally cracked Brazilian disk[J]. 2017, 38(8): 2395-2401. DOI： 10.16285/j.rsm.2017.08.029.

摘要

从理论和数值两个方面进行分析，发现受径向集中力和围压作用的中心裂纹圆盘（CCBD）试件裂纹面接触会对II型应力强度因子产生较大的影响。通过理论研究，分析CCBD受集中力和围压作用裂纹面接触时圆盘内部的应力场，采用断裂力学权函数理论，推导得出在集中力和围压共同作用下，考虑裂纹面闭合时应力强度因子的解析解。然后，使用ANSYS软件建立了相应的数值模型计算应力强度因子，并与理论解和相关文献进行对比验证，证明了理论公式的正确性。无论裂纹张合与否，所提出的解析公式都能计算出不同裂纹长度、加载角、围压和摩擦系数的应力强度因子。最后，利用公式分析摩擦系数对应力强度因子的影响，结果表明：随着摩擦系数的增大，I型裂纹的应力强度因子不变，II型裂纹的应力强度因子随之显著减小；当加载角较大时，裂纹面产生更为复杂的二次裂纹，故压剪断裂测试的推荐加载角范围为30°～50°。

Abstract

Analytic solutions and numerical solutions were employed to analyze the effect of the crack face contacting on the Mode-II stress intensity factors (SIFs). The crack face of the centrally cracked Brazilian disk (CCBD) specimen was subjected to both the confining pressure and diametrical force. Through the theoretical study

the stress field inside the CCBD specimen was analyzed under different loading conditions when the crack surface contacted. Then

an analytical formula was obtained for calculating the Mode-II SIFs in CCBD specimen under different loading conditions by using the weight function method. Meanwhile

a numerical modeling by ANSYS software is used to calculate the corresponding SIFs. By comparing numerical results and theoretical solutions

it is found that they are in good agreement

which indicates that the reliability of the theoretical analysis is valid. Even if the crack is closing

the SIFs can be obtained explicitly and easily for any arbitrary relative crack length

loading angle

confining pressure and friction coefficient. Finally

the effect of the coefficient of friction on SIFs in a CCBD specimen was investigated. The results show that the Mode-II SIF decreased significantly with the increase of friction coefficient

while the Mode-I SIF was constant. In addition

more complex secondary cracks were produced on the crack surface when the load angle was larger. Hence

the recommended loading angle range is 30°~50° for compression-shear fracture tests.

关键词

Keywords

references

Views

169

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Mesh independence of numerical manifold method in treating strong singularity

Study of effect of cracking orientation on tunnel stability

Research on effective elastic mechanical properties of medium rank coal

Research on triaxial compression test of granite after high temperatures

Methods for testing permeability of deep mudstone and analysis of data reliability of each method

Related Author

XU Dong-dong

ZHENG Hong

LI Yuan-xin

ZHU Zhe-ming

LIU Kai

FAN Jun-li

FAN Tie-gang

ZHANG Guang-qing

Related Institution

State Key Laboratory of Geomechanics and Geotechnical Engineering, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences

School of Architecture and Environment, Sichuan University

College of Mechanical and Transportation Engineering, China University of Petroleum

College of Petroleum Engineering, China University of Petroleum

Langfang Branch, Petroleum China Research Institute of Exploration & Development

AI问答

⁰