Implementation of a plasticity model for large post-liquefaction deformation of sand in FLAC3D

ZOU You-xue; WANG Rui; ZHANG Jian-min

doi:10.16285/j.rsm.2016.1237

English Version Journal Login

您当前的位置：

首页 >

文章列表页 >

Implementation of a plasticity model for large post-liquefaction deformation of sand in FLAC3D

更新时间：2026-06-25

- Implementation of a plasticity model for large post-liquefaction deformation of sand in FLAC3D
- Vol. 39, Issue 4, Pages: 1525-1534(2018)
- 作者机构：
  
  1. 清华大学水沙科学与水利水电工程国家重点实验室,北京,100084
  2. 清华大学土木水利学院,北京,100084
- 作者简介：
- 基金信息：
- DOI：10.16285/j.rsm.2016.1237
  CLC： TU441
- Online First：06 June 2018，
  
  Published：2018
- 稿件说明：
移动端阅览
ZOU You-xue, WANG Rui, ZHANG Jian-min. Implementation of a plasticity model for large post-liquefaction deformation of sand in FLAC3D[J]. 2018, 39(4): 1525-1534.
DOI：

ZOU You-xue, WANG Rui, ZHANG Jian-min. Implementation of a plasticity model for large post-liquefaction deformation of sand in FLAC3D[J]. 2018, 39(4): 1525-1534. DOI： 10.16285/j.rsm.2016.1237.

摘要

通过FLAC3D二次开发平台，在VC++环境下实现了基于砂土液化大变形机制的变动映射中心边界面弹塑性模型的二次开发。基于饱和砂土液化大变形本构理论，该模型符合三维应力空间边界面映射规则，并引入临界状态变量，可实现对不同密度和围压状态下砂土液化大变形分析。针对FLAC3D程序混合离散技术与数据调用模式和模型的体积相容性条件，测试分析了将模型采用不同植入方案的计算稳定性，开发了在FLAC3D混合离散技术下不同子区共享映射中心，进入与离开液化状态保持同步的开发方案，并给出模型开发的关键技术与实施方法。利用开发的模型，对饱和砂土开展了不排水/排水/循环三轴试验与不排水循环扭剪试验模拟，及三维地基的动力反应分析。计算结果表明，模型及所开发程序具有很好的模拟与分析砂土液化后大变形的能力。

Abstract

The purpose of the study is to improve the simulation of liquefaction of sands and variations in effective stress when using FLAC3D for the dynamic analysis of liquefiable ground and structures. Based on the physics of large post-liquefaction deformation of sand

a bounding surface plasticity model with appropriate mapping rules for plasticity and dilatancy in three-dimensional stress space is developed. A state parameter for compatibility with critical state soil mechanics enables the simulation of sand at various densities and confining pressures with a same set of parameters. According to requirements and procedures of user-defined-model (UDM)

the plasticity model is successfully implemented into FLAC3D code in Visual C++ environment. After testing the calculation stability

the implemented schematics allow subzones of the mixed discretization process in FLAC3D share mapping center and simultaneously enter and leave liquefaction status. Using the program

undrained and drained triaxial tests

cyclic triaxial tests

undrained cyclic torsional tests are simulated and a three-dimensional site dynamic response analysis is also performed. The results show that the model and the implemented program have superior and reasonable capability to simulate small and large deformation in pre- to post-liquefaction phase of sand.

关键词

Keywords

references

Views

630

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Development and verification of bounding surface model in FLAC3D

Development and implementation of Duncan-Chang constitutive model in FLAC3D

Stability analysis of close-located underground caverns based on tunnel lining and equivalent anchor bolt simulation

Determination of engineering parameters based on mutable characteristics of monitored values in numerical simulation

Numerical model and validation of failure mode for underground caverns in layered rock mass

Related Author

LEI Xiao-qin

YANG Guo-lin

CHEN Yu-min

LIU Han-long

LIU Jie

TANG Liang

LI Jian-lin

HU Jing

Related Institution

School of Civil Engineering, Central South University

LGCIE, INSA Lyon, Villeurbanne

Institute of Geotechnical Engineering, Hohai University

Key Laboratory of Geological Hazards on Three Gorges Reservoir Area, Ministry of Education, China Three Gorges University

College of Hydraulic & Environmental Engineering, China Three Gorges University

AI问答

⁰