Research and Application of Secondary Cable Laying Technology in Substation Based on BRCM Software

ZHANG Xiaobing; LI Can; WANG Kun; LING Zhiyong; ZHANG Yi; ZHOU Chao

English Version Reader LoginJournal Login

您当前的位置：

首页 >

文章列表页 >

Research and Application of Secondary Cable Laying Technology in Substation Based on BRCM Software

更新时间：2025-11-18

- Research and Application of Secondary Cable Laying Technology in Substation Based on BRCM Software
- Vol. 42, Issue 3, Pages: 55-58(2022)
- 作者机构：
  
  1. 国网株洲供电分公司
  2. 湖南工业大学电气与信息工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC： TM63;TM757
- Published：2022
- 稿件说明：
移动端阅览
ZHANG Xiaobing, LI Can, WANG Kun, et al. Research and Application of Secondary Cable Laying Technology in Substation Based on BRCM Software[J]. 2022, 42(3): 55-58.
DOI：

ZHANG Xiaobing, LI Can, WANG Kun, et al. Research and Application of Secondary Cable Laying Technology in Substation Based on BRCM Software[J]. 2022, 42(3): 55-58. DOI：

摘要

针对二维设计模式下变电站二次电缆量开列不准、无法满足精准投资的问题，提出运用BRCM三维软件建模，实现变电站二次电缆按照优化路径自动敷设。首先，详细介绍了BRCM软件进行电缆敷设设计的流程；其次，以某110 kV变电站为例，建立了变电站电缆沟、电缆支架、电气设备三维模型，设置电缆敷设原则，可一键导出路径优化后的电缆清册；最后，通过二维设计电缆估算量、三维模拟优化路径后对电缆量与实际变电站电缆用量进行对比分析。结果表明，应用BRCM软件后，比二维设计电缆总量减少投资10.8%

达到了精准投资的成效，且与实际电缆敷设总量误差在5%以内，符合工程规范要求，体现了BRCM三维建模路径优化的可行性和可靠性。

Abstract

In order to avoid the inaccurate listing of substation secondary cable quantity under the two-dimensional design mode

which cannot meet the requirements of current precise investment

the paper proposes to use BRCM three-dimensional software modeling to realize automatic laying of substation secondary cable according to the optimized path. Firstly

the process of cable laying design by BRCM software is introduced in detail. Secondly

taking a certain 110 kV substation as an example

the three-dimensional model of substation cable trench

cable bracket and electrical equipment is established. The cable laying principle is set

and the cable list with optimized path can be exported with one click. Finally

the estimated cable consumption of two-dimensional design and the actual cable consumption of three-dimensional simulation optimized path are compared and analyzed. The data show that

with the application of BRCM software

the investment is reduced by 10.8% compared with the total amount of two-dimensional design cable

and the result of precise investment is achieved. The error between BRCM software and the actual cable laying amount is less than 5%

which meets the requirements of engineering specifications.It shows the feasibility and reliability of the path optimization of BRCM 3 D modeling.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

A new general monitor platform design

Safety evaluation for grounding grid of substation on 220 kV or above in Hunan province

Development on the intelligent evaluation system of the substation simulation training system

Application of sound intensity method in sound power level measure of power transformer

“one stop one analysis”substation platform based on WEB

Related Author

LU Suo-wang

MAO Wen-qi

JIANG Zheng-long

WANG Xin-xiu

MA Xiao-fei2

WANG Yan1

ZHOU Nian-Guang

LV Jian-hong

Related Institution

Dazhen irrigation management burea u

湖南省电力试验研究院湖南长沙410007

Hunan Electric Power Test and Research Institute

Hunan Electric Power Corporation EHA Transmission & Transformation Bureau

Hunan Electric Power Corporation Training Center

AI问答

⁰