A new method for calculating roughness angle ?? in Maksimovic peak shear strength criterion of rock joints

TANG Zhi-cheng; LIU Quan-sheng; XIA Cai-chu; WU Yue-xiu; HUANG Ji-hui; WANG Chun-bo

English Version Journal Login

您当前的位置：

首页 >

文章列表页 >

A new method for calculating roughness angle ?? in Maksimovic peak shear strength criterion of rock joints

更新时间：2026-06-25

- A new method for calculating roughness angle ?? in Maksimovic peak shear strength criterion of rock joints
- Vol. 35, Issue 2, (2014)
- 作者机构：
  
  1. 武汉大学土木建筑工程学院,武汉,430072
  2. 同济大学地下建筑与工程系,上海,200092
- 作者简介：
- 基金信息：
- DOI：
  CLC： TU44
- Online First：18 February 2014，
  
  Published：2014
- 稿件说明：
移动端阅览
TANG Zhi-cheng, LIU Quan-sheng, XIA Cai-chu, et al. A new method for calculating roughness angle ?? in Maksimovic peak shear strength criterion of rock joints[J]. 2014, 35(2).
DOI：

TANG Zhi-cheng, LIU Quan-sheng, XIA Cai-chu, et al. A new method for calculating roughness angle ?? in Maksimovic peak shear strength criterion of rock joints[J]. 2014, 35(2). DOI：

摘要

岩石节理的非线性Maksimovic峰值抗剪强度准则，采用双曲线函数描述不同法向应力作用下剪胀角的变化，参数物理含义明确、适用的法向应力范围广且形式简洁。采用的参量“粗糙度角 ”反映节理的粗糙程度，但由至少3组直剪试验数据回归分析确定，因此，不能采用该准则估算节理的峰值抗剪强度。通过等价关系，由已有的峰值抗剪强度准则得到用三维形貌参数表示的“粗糙度角 ”，提出含三维形貌参数的Maksimovic峰值抗剪强度准则。采用不同形貌节理的直剪试验数据对准则进行了验证，结果表明，计算值与试验值吻合较好，验证了公式的正确性；同时，亦与经典的Barton准则进行了对比。可用该准则预估节理的峰值抗剪强度。

Abstract

A nonlinear peak shear strength criterion

proposed by Maksimovic

uses a simple hyperbolic function to describe the peak dilatancy angle under different normal stresses. The model has significant advantages

such as parameters have physical meaning

law is valid from zero to infinity

and it is simpler from the view of mathematical point. The roughness of joint surface is expressed by the parameter of “roughness angle

”

obtained by using the least square fit method on basis of at least three sets of measured data. It is not easy to use the Maksimovic criterion to predict the peak shear strength of rock joints. In this paper

the roughness angle is determined by a rational method with a quantitative three dimensional morphology parameters of joint surface. Then

a modified Maksimovic peak shear strength criterion is proposed. Several experimental results are used for verification of the proposed relations. It is shown that the calculated values are in good agreement with the measured data. It also presents the comparison between the new criterion with the famous Barton’s criterion. We can use the proposed criterion as a useful tool to predict the peak shear strength for rock joints.

关键词

Keywords

references

Views

1276

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Shear mechanical model for soil-rock interface considering roughness effects

Fractal characteristics of joint surface morphology of Pengshui shale and anisotropic characterization based on joint roughness coefficient

Characterization of charge sensing signals during slip destabilization of faults with different roughness rock interfaces

Particle flow analysis of direct shear tests on joints with different roughnesses

A new fractal description method for three-dimensional roughness surface of rock joint

Related Author

HUANG Ye-ning

DENG Hua-feng

KONG Gang-qiang

LI Jian-lin

ZHU Zuo-xiang

ZHOU Shu-huan

LI Guan-ye

DONG Jia-bin

Related Institution

Key Laboratory of Ministry of Education for Geomechanics and Embankment Engineering, Hohai University

Key Laboratory of Geological Hazards on Three Gorges Reservoir Area, Ministry of Education, China Three Gorges University

School of Resources and Environment, Henan Polytechnic University

Henan Key Laboratory of Coal Measure Unconventional Resources Accumulation and Exploitation, Henan Polytechnic University

Collaborative Innovation Center of Coal Work Safety and Clean High Efficiency Utilization, Henan Polytechnic University

AI问答

⁰