Comparison and analysis of 2D and 3D slope stability analysis results

LU Kun-lin; ZHU Da-yong; YANG Yang

English Version Journal Login

您当前的位置：

首页 >

文章列表页 >

Comparison and analysis of 2D and 3D slope stability analysis results

更新时间：2026-06-25

- Comparison and analysis of 2D and 3D slope stability analysis results
- Vol. 33, Issue S2, (2012)
- 作者机构：
  
  合肥工业大学土木与水利工程学院,合肥,230009
- 作者简介：
- 基金信息：
- DOI：
  CLC： TU473
- Online First：11 December 2012，
  
  Published：2012
- 稿件说明：
移动端阅览
LU Kun-lin, ZHU Da-yong, YANG Yang. Comparison and analysis of 2D and 3D slope stability analysis results[J]. 2012, 33(S2).
DOI：

LU Kun-lin, ZHU Da-yong, YANG Yang. Comparison and analysis of 2D and 3D slope stability analysis results[J]. 2012, 33(S2). DOI：

摘要

二维与三维边坡稳定性分析得到的安全系数存在着差异，讨论这种差异与滑体几何尺寸及土体强度参数间的变化规律及其形成机制，可为合理地评价边坡稳定性分析提供理论依据。针对均质三维边坡，利用基于滑面正应力修正模式的极限平衡法分析程序，定性地讨论滑体形态、长高比、坡比、土体强度参数等指标对二维与三维安全系数计算结果差异(以F3/F2表示)的影响，总结F3/F2与影响指标间的变化规律，分析变化规律形成的内在机制。从工程应用的角度，给出需要考虑该差异影响的分界标准。研究表明，F3/F2随着长高比L/H、内摩擦角?及坡比m的增大逐渐减小，随着黏聚力c的增大逐渐增大；对于满足下列条件之一的边坡，宜采用三维安全系数来评价其稳定性，(1) L/H ≤ 5的滑坡体；(2) 5< L/H ≤ 10且 c > 25 kPa(或? < 15°，或m < 1.0) 的滑坡体。研究成果可为合理评价边坡稳定性分析方法提供参考。

Abstract

Relationships between the difference of 2D and 3D safety factor and parameters of landslide geometry (including ratio of slope

3D sliding mass shape and length of landslide) and soil strength (including cohesion and internal friction angle) are studied. 2D and 3D safety factor of the different parameters homogeneous slopes are calculated based on the slope stability analysis program of the limit equilibrium method by modifying normal stress over slip surface. The ratio of 3D to 2D safety factor (denoted by F3/F2) is used to analyze the difference of 2D and 3D safety factor. Then

variation rule and mechanism of F3/F2 by changing parameters of landslide geometry and soil strength are also discussed. Finally

the standard of ignoring the difference of 2D and 3D safety factor are proposed from the view point of engineering practice. Results show that: F3/F2 decreases while ratio of length to height

internal friction angle and ratio of slope increases

and increases when cohesion increases; 3D safety factor is suggested to estimate the slope stability when (1) ratio of length to height is lower than or equivalent to 5; (2) ratio of length to height is more than 5 and lower than or equivalent to 10 while cohesion more than 25 kPa or internal friction angle lower than 15° or ratio of slope lower than 1. The conclusion can be referring to correct evaluation of slope stability.

关键词

Keywords

references

Views

2388

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Selection of constitution and distribution model of normal stresses over slip surface of slope

Analysis of slope stability based on modified relationship of intermediate principal stress

Three-dimensional stability analysis of slope with weak interlayer

Study of slope stability under blasting vibration based on distribution of normal stress over slip surface

Search of three-dimensional slip surface for slope based on finite element calculation

Related Author

LU Kun-lin

ZHU Da-yong

YANG Yang

GONG Wen-jun

ZENG Li-feng

SUN Jun-jie

LI Ming-yong

WANG Hao-ran

Related Institution

Anhui Key Laboratory of Civil Engineering and Materials, Hefei University of Technology

Department of Civil Engineering, Beihang University

State Key Laboratory of Structural Analysis for Industrial Equipment, Dalian University of Technology

Lanzhou Institute of Seismology, China Earthquake Administration

Department of Geotechnical Engineering, Tongji University

AI问答

⁰