Mechanical properties and anti-abrasion performance of 00Cr13Ni4Mo super martensitic stainless steel

DONG Fangqi; YANG Baixun; LI Yimin; TIAN Xiao

English Version Reader LoginJournal Login

您当前的位置：

首页 >

文章列表页 >

Mechanical properties and anti-abrasion performance of 00Cr13Ni4Mo super martensitic stainless steel

更新时间：2025-09-28

- Mechanical properties and anti-abrasion performance of 00Cr13Ni4Mo super martensitic stainless steel
- Thermal Power Generation Vol. 45, Issue 3, Pages: 110-115(2016)
- 作者机构：
  
  西安热工研究院有限公司
- 作者简介：
- 基金信息：
- DOI：
  CLC： TG142.71
- Published：2016
- 稿件说明：
移动端阅览
DONG Fangqi, YANG Baixun, LI Yimin, et al. Mechanical properties and anti-abrasion performance of 00Cr13Ni4Mo super martensitic stainless steel[J]. Thermal power generation, 2016, 45(3): 110-115.
DOI：

DONG Fangqi, YANG Baixun, LI Yimin, et al. Mechanical properties and anti-abrasion performance of 00Cr13Ni4Mo super martensitic stainless steel[J]. Thermal power generation, 2016, 45(3): 110-115. DOI：

摘要

通过扫描电镜、透射电镜、硬度与冲击试验以及冲刷磨损试验

对超级马氏体不锈钢00Cr13Ni4Mo在8种不同热处理工艺下的力学性能与抗磨蚀性能进行了研究。结果表明:00Cr13Ni4Mo钢在550~650℃回火后产生逆变奥氏体

逆变奥氏体降低了材料的强度与硬度

增加了材料的韧性;00Cr13Ni4Mo钢的抗磨蚀性能主要与硬度有关

而与其冲击韧性关系较小;从材料性能和经济性综合考虑

00Cr13Ni4Mo钢最佳热处理工艺为1 050℃/9h正火+550℃/6h一次回火处理。

Abstract

The mechanical properties and anti-abrasion properties of 00Cr13Ni4 Mo super martensitic stainless steel under 8heat treatment processes were investigated

through a series of tests

such as scanning electron microscopy analysis

transmission electron microscopy analysis

hardness and impact test

and the erosion wear test.The results show that

the reverse austenite formed after the 00Cr13Ni4 Mo steel was tempered at 550℃to 650℃

which reduced the strength and hardness of the material and increased the toughness of the material.The anti-abrasion performance of the 00Cr13Ni4 Mo steel is primarily related to its hardness

while the material's toughness affected little.Comprehensively considering the properties and the economy

being normalized at 1 050 ℃for 9hand first tempered at 550 ℃for 6his the most suitable heat treatment process for this kind of steel.

关键词

Keywords

references

Views

314

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

HEAT TREATMENT PROCESS AND MICRO-SCOPIC STRUCTURE OF WB36 STEEL

THE CARBIDE CONTAINED IN HCM25(T23) STEEL AND EVOLUTION REGULARITY THEREOF

STUDY ON SERVICING BEHAVIOR OF BOILER TUBES MADE FROM 18-8 TYPE AUSTENITIC STAINLESS STEEL(6)

TEST ASSESSMENT OF INDUCTIVE PIPEBENDING WITH BENDING RADIUS OF 1.5 D AND APPLICATION THEREOF

STUDY ON PERFORMANCE OF HIGH HARDNESS AND LOW HARDNESS WELD JOINTS ON P91 MAIN STEAM PIPE

Related Author

ZHAO Qiang

WANG Ran

PENG Xian-kuan

AN Wei

CONG Xiang-zhouBeijing Guodian Futong Science and Technology Development Co Ltd

YU Zaisong1

NIE Ming2

HOU Shufang1

Related Institution

Beijing Guodian Futong Technology Development Co., Ltd

Guangdong Power Grid Corporation Electric Power Science Research Institute

Yangzi Petrochemical Shaoer Pipe Industry Co., Ltd

Nanjing University of Technology

Xigu Thermal Power Co., Ltd

AI问答

⁰